hellswindstaff Posted March 21, 2014 Posted March 21, 2014 (edited) Looking to make something similar but different than the wrist roller shown below, but the one in the picture seems to be secured with a hose clamp. I've used this method but the hose clamp almost always breaks or spins with heavy weights. Does anyone have any ideas for securing a rope, chain, or anything to hang the weight from to the PVC that is rotating around the mounted piping? http://www.straighttothebar.com/images/posts/081218_rackmountedwristroller.jpg Edited March 21, 2014 by hellswindstaff Quote
climber511 Posted March 21, 2014 Posted March 21, 2014 Look up "timber hitch" - tie the rope on using that know and cover it with duct tape - it has held everything I could throw at it for several years now. 1 Quote When people used to ask him how it was he became so incredibly strong, it was always the same, "strengthen your mind, the rest will follow". The Mighty Atom Age wrinkles the body. Quitting wrinkles the soul. Being prepared for any random task is not the same thing as preparing randomly for any task. Greg Everett
Frank Pizzo Posted March 21, 2014 Posted March 21, 2014 I made my wrist roller about 7 years ago and what I did was just drill a small hole through one side and out the other on the pvc pipe then tie a big not that doesn't fit through the hole...its never slipped out in 7 years, but the rope itself has broken on several occasions. Not the most elaborate solution, but it worked for me. Quote "Gold medals aren't really made of gold. They're made of sweat, determination, and a hard-to-find alloy called guts." - Dan Gable
climber511 Posted March 21, 2014 Posted March 21, 2014 Look up "timber hitch" - tie the rope on using that know and cover it with duct tape - it has held everything I could throw at it for several years now. This has the advantage of no knot inside so it rolls freely on the inner bar. 1 Quote When people used to ask him how it was he became so incredibly strong, it was always the same, "strengthen your mind, the rest will follow". The Mighty Atom Age wrinkles the body. Quitting wrinkles the soul. Being prepared for any random task is not the same thing as preparing randomly for any task. Greg Everett
Frank Pizzo Posted March 21, 2014 Posted March 21, 2014 Look up "timber hitch" - tie the rope on using that know and cover it with duct tape - it has held everything I could throw at it for several years now. This has the advantage of no knot inside so it rolls freely on the inner bar. The knot is on the outside, the rope goes through the pvc pipe and turns around the bar as you spin it. I'm not saying its the best way, but I didn't have to buy anything else, and like I said its lasted. However your method is probably better, I'm just throwing out options. Quote "Gold medals aren't really made of gold. They're made of sweat, determination, and a hard-to-find alloy called guts." - Dan Gable
Cannon Posted March 21, 2014 Posted March 21, 2014 I made a PVC sleeve with friction tape that slides over an axle while in a power rack. Maybe $5-10. http://www.gripboard.com/uploads/1266226852/gallery_9552_555_71464.jpg http://www.gripboard.com/uploads/1266226852/gallery_9552_555_115195.jpg Quote
slazbob Posted March 21, 2014 Posted March 21, 2014 (edited) I actually use a carabiner... The kind that looks like a small chain link. I wrap the cable around a couple times, then I get the end with the carabiner and hook it around the cable that's going down from the wrist roller. Once i get some weight on there it gets tight and stays put. I'm not sure if will work on PVC but if it does, that's good. Edited March 21, 2014 by slazbob Quote
Gary Gray Posted March 21, 2014 Posted March 21, 2014 I made a PVC sleeve with friction tape that slides over an axle while in a power rack. Maybe $5-10. http://www.gripboard.com/uploads/1266226852/gallery_9552_555_71464.jpg http://www.gripboard.com/uploads/1266226852/gallery_9552_555_115195.jpg My Wrist Roller is exactly like the one in the picture posted by Cannon. Used in a Power Rack, same PVC Sleeve, Friction Tape and Hose Clamp . Not only very low cost, works great and has advantage of using a fat grip (the outside diameter of my Sleeve is 2-1/2") Quote
rico300zx Posted March 22, 2014 Posted March 22, 2014 watch my videos on wrist roller how to make one really easythat is rack mounted Quote Dare to compare? Check out some of my lifts at.........http://www.youtube.com/rico300zx My gripboard gallery http://www.gripboard.com/index.php?/gallery/album/1037-coc/ Parris Janusek
hellswindstaff Posted March 27, 2014 Author Posted March 27, 2014 I probably should have specified before fellows, but I'm actually trying to avoid the thicker grip bc my hands will be maxed out before my wrists are even worked. I'm trying to stick to a width of 1"-1.5". Thank you all for your advice so far though Quote
climber511 Posted March 27, 2014 Posted March 27, 2014 (edited) I probably should have specified before fellows, but I'm actually trying to avoid the thicker grip bc my hands will be maxed out before my wrists are even worked. I'm trying to stick to a width of 1"-1.5". Thank you all for your advice so far though Well that changes things a bit . If you have a power rack with 1" pins you can use 1 1/4" PVC as a sleeve - use the Timber Hitch I spoke of (or a hose clamp) - that sleeve will turn freely enough (only make it about 16" long). That will give an outside diameter of 1 5/8". Various combinations of inner"axle" size and outer PVC (or steel) can give you what you want. Edited March 27, 2014 by climber511 Quote When people used to ask him how it was he became so incredibly strong, it was always the same, "strengthen your mind, the rest will follow". The Mighty Atom Age wrinkles the body. Quitting wrinkles the soul. Being prepared for any random task is not the same thing as preparing randomly for any task. Greg Everett
hellswindstaff Posted March 27, 2014 Author Posted March 27, 2014 I probably should have specified before fellows, but I'm actually trying to avoid the thicker grip bc my hands will be maxed out before my wrists are even worked. I'm trying to stick to a width of 1"-1.5". Thank you all for your advice so far though Well that changes things a bit . If you have a power rack with 1" pins you can use 1 1/4" PVC as a sleeve - use the Timber Hitch I spoke of (or a hose clamp) - that sleeve will turn freely enough (only make it about 16" long). That will give an outside diameter of 1 5/8". Various combinations of inner"axle" size and outer PVC (or steel) can give you what you want. Do you think that very heavy weights could be used wiht the timber hitch? Quote
PeterSweden Posted March 27, 2014 Posted March 27, 2014 I use a 2'' pipe and 550 paracord and duct tape. Tied a knot around the steel pipe, on the middle and then I took tape to secure it and preventing it from spinning. I put the pipe in my squat rack and just roll it up. It never spins, it never losens up and it always works. You can take whatever '' pipe you want and do this. I have rolled 80kilos with it without any problems. Did you understand? If not, I can take a picture. Easiest WR you'll ever make 1 Quote Grip goals for 2016 - we'll see how many of these I can cross off; Grippers; Cert GHP7, CCS 140, 146, 153 and 157lbs CoC3, MMS and 20mmBS 180lbs CoC3,5. Pinch; Clean 20kg blockweight, curl 20kg blockweight, 1h euro pinch 45kg.
climber511 Posted March 27, 2014 Posted March 27, 2014 I probably should have specified before fellows, but I'm actually trying to avoid the thicker grip bc my hands will be maxed out before my wrists are even worked. I'm trying to stick to a width of 1"-1.5". Thank you all for your advice so far though Well that changes things a bit . If you have a power rack with 1" pins you can use 1 1/4" PVC as a sleeve - use the Timber Hitch I spoke of (or a hose clamp) - that sleeve will turn freely enough (only make it about 16" long). That will give an outside diameter of 1 5/8". Various combinations of inner"axle" size and outer PVC (or steel) can give you what you want. Do you think that very heavy weights could be used wiht the timber hitch? Depends what you call heavy I guess - it held with a couple hundred pounds more or less for me. Quote When people used to ask him how it was he became so incredibly strong, it was always the same, "strengthen your mind, the rest will follow". The Mighty Atom Age wrinkles the body. Quitting wrinkles the soul. Being prepared for any random task is not the same thing as preparing randomly for any task. Greg Everett
hellswindstaff Posted March 28, 2014 Author Posted March 28, 2014 Awesome... thanks so much guys. Gripboard rules! I probably should have specified before fellows, but I'm actually trying to avoid the thicker grip bc my hands will be maxed out before my wrists are even worked. I'm trying to stick to a width of 1"-1.5". Thank you all for your advice so far though Well that changes things a bit . If you have a power rack with 1" pins you can use 1 1/4" PVC as a sleeve - use the Timber Hitch I spoke of (or a hose clamp) - that sleeve will turn freely enough (only make it about 16" long). That will give an outside diameter of 1 5/8". Various combinations of inner"axle" size and outer PVC (or steel) can give you what you want. Do you think that very heavy weights could be used wiht the timber hitch? Depends what you call heavy I guess - it held with a couple hundred pounds more or less for me. That should do... at least until I'm wrist rolling with a couple thousand pounds :P Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.