TylerA Posted January 19, 2014 Share Posted January 19, 2014 I recently went to the hardware store to try out some 1/4" colled rolled steel. For some reason, this stuff feels easier than my 60D's. Are 60D stronger? Here is a video of my bend: http://www.youtube.com/watch?v=LOojTUBcHAY Quote Link to comment Share on other sites More sharing options...
Tom Scibelli Posted January 19, 2014 Share Posted January 19, 2014 Good job, try a 6"X1/4" grade 5 bolt now, it will be harder than 1/4crs/60D Quote Link to comment Share on other sites More sharing options...
Josh O'Dell Posted January 19, 2014 Share Posted January 19, 2014 All depends on the brand. I never really messed with 1/4 crs just 1/4 stainless and grade2 1/4 6in bolts You may wanna even try a grade5 1/4 6in bolt. Just get various stock to try .. Quote Link to comment Share on other sites More sharing options...
Josh O'Dell Posted January 19, 2014 Share Posted January 19, 2014 And at some point you will need some 7in stock to practice for the red That inch makes a word of difference..... 1 Quote Link to comment Share on other sites More sharing options...
Tim71 Posted January 21, 2014 Share Posted January 21, 2014 Tyler, First off, nice job on that bend. I've studied steel and had more stock calibrated than you can imagine so I'll try and shed some light on your question. First, the 60d nails. Average 60d takes about 250 to 275 pounds of pressure to bend. I've had them calibrated at 210 pounds all the way up to freaky 480 pounds. Anything over 300 pounds is a pretty mean 60d though. Now, cold rolled steel can also have a lot of variance depending on the brand and other factors. If you bought this cold rolled steel in the 3 or 4 foot pre-made sections then it's likely easier. The 1018 cold rolled steel you buy from a steel supplier is almost always tougher and more comparable to a 60d. If the cold rolled steel you are bending is the zinc-plated stuff then it's even noticeably easier but it's very mild carbon steel. Steel works and National are 2 brands of the easier stuff. Trying a 6 inch G5 bolt is good advice but could be a frustrating jump up from what you are bending now. If you have a Fastenal near by, try some 1/4 inch drill rod. Also, I've gotten some 1045 1/4 inch cold rolled steel from Fastenal before and it's a good bridge to the G5 bolt. Also, where did you buy your 60d nails? Griprites from Lowes are usually the easier ones but they also can vary a lot and the last batch I just bought are surprisingly hard. If you can find Keystones or the American made Mazels, those are usually very consistant and in the low 300ish pounds. Mazel also has some Chinese made ones now that I haven't tried. Hope this helps. Quote Link to comment Share on other sites More sharing options...
Tim71 Posted January 21, 2014 Share Posted January 21, 2014 Tyler, Just checked out your other videos and loved the "pot holder" bend. I can remember first starting and using kitchen towels and whatever I could find to start bending. Quote Link to comment Share on other sites More sharing options...
acromegaman Posted January 22, 2014 Share Posted January 22, 2014 I started with paper towels and a little duct tape. Lol 1 Quote Link to comment Share on other sites More sharing options...
Josh O'Dell Posted January 22, 2014 Share Posted January 22, 2014 I started out with table cloths.. Quote Link to comment Share on other sites More sharing options...
acromegaman Posted January 22, 2014 Share Posted January 22, 2014 What we do to feed our addiction Quote Link to comment Share on other sites More sharing options...
Josh O'Dell Posted January 22, 2014 Share Posted January 22, 2014 Lol tell me about it, bending junkies are fix is a New order of steel or some hareware store goodies Lol Quote Link to comment Share on other sites More sharing options...
Tim71 Posted January 22, 2014 Share Posted January 22, 2014 Tell me about it. Many a times have me and family been on vacation and I spot a nice little hardware store and a couple minutes and a U-turn later and I'm on my way to check out the goodies. Quote Link to comment Share on other sites More sharing options...
Josh O'Dell Posted January 22, 2014 Share Posted January 22, 2014 Lol Quote Link to comment Share on other sites More sharing options...
TylerA Posted January 27, 2014 Author Share Posted January 27, 2014 Thank for all your comments Right now I'm looking at these: http://www.homedepot.com/p/Grip-Rite-60D-Bright-Steel-Spikes-50-lb-Pack-60C/100192956 I want to get something in bulk like this so I can mass bend for cheap. Anyone know anything about these nails? Are they strong enough? Quote Link to comment Share on other sites More sharing options...
acromegaman Posted January 28, 2014 Share Posted January 28, 2014 They don't say anything about double overhand bending in the description, but I'm pretty sure they'll work Quote Link to comment Share on other sites More sharing options...
acromegaman Posted January 28, 2014 Share Posted January 28, 2014 They'll be good for warmups before too long, but where I seen most of my gains was really pushing myself and going at a bar that I knew was just out of my reach and slowly but surely bending it over a session or two after I warm up of course. I'd go with Tom's previous comment about the g5 1/4x6 1 Quote Link to comment Share on other sites More sharing options...
Josh O'Dell Posted January 28, 2014 Share Posted January 28, 2014 Thats fine i would also suggest the beginner bag from fbbc.. Quote Link to comment Share on other sites More sharing options...
Tim71 Posted January 29, 2014 Share Posted January 29, 2014 That is a good price on a 50 pound box. I might look at some of those myself. As for how hard they are? Like I said above, totally depends on the batch. I've never had a bright 60d that was under 250 pounds though so I'd say it's a pretty safe bet. I'll agree with the above post about attacking a piece of steel outside your range and basically getting some iso work in but I also know that I need to bend some steel to keep it interesting. Also, when I'm in a bending session, I like to work my way up and warm up good and that's usually when I do my best work. Also, if you can bend a 60d in some quickly applied single wraps, you can show off to the non-bending world and they will pretty much be awe-struck. I've bent G5s and G8s for people and the 60d gets as much of a response if not better. Later Quote Link to comment Share on other sites More sharing options...
TylerA Posted January 29, 2014 Author Share Posted January 29, 2014 That is a good price on a 50 pound box. I might look at some of those myself. As for how hard they are? Like I said above, totally depends on the batch. I've never had a bright 60d that was under 250 pounds though so I'd say it's a pretty safe bet. I'll agree with the above post about attacking a piece of steel outside your range and basically getting some iso work in but I also know that I need to bend some steel to keep it interesting. Also, when I'm in a bending session, I like to work my way up and warm up good and that's usually when I do my best work. Also, if you can bend a 60d in some quickly applied single wraps, you can show off to the non-bending world and they will pretty much be awe-struck. I've bent G5s and G8s for people and the 60d gets as much of a response if not better. Later Its because most people have no idea how incredibly strong G8 bolts are. By looks alone, the 60D is more of a beast! Quote Link to comment Share on other sites More sharing options...
climber511 Posted January 29, 2014 Share Posted January 29, 2014 Find a steel retailer where you can buy lengths of steel. Cold Roll comes in 12' lengths but most places will cut it in half (usually for no charge) so you can fit it in your car if necessary, I just bought 3 12' lengths of 1/4" CRR (cold roll round) yesterday - it cost $12.10 plus tax - and it will fit uncut into a mini van, barely. Quote Link to comment Share on other sites More sharing options...
Josh O'Dell Posted January 29, 2014 Share Posted January 29, 2014 I do the same i paid 8 bucks at the local machine shop and Got 40 7" 5/16th peices and they are about like a red;) Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.