rolf Posted June 17, 2012 Share Posted June 17, 2012 I'm starting to work towards no-set closing a COC #2.5. I'll start by closing it to 12 mm from fully closed for singles and work from there towards fully closed over the next few months, hopefully. I've taped together a stack of coins that measures 12 mm thick. Then I'll remove coins from the stack every now and then. This will work, but I was wondering if anyone makes something that could be used for this kind of training with "target gaps". The CoC Key will not work, as it's meant for measuring the gap and thus the different thickness surfaces are way too tiny to aim at. Quote Link to comment Share on other sites More sharing options...
chilliman64 Posted June 17, 2012 Share Posted June 17, 2012 you're referring to 'set blocks'. Grippersuperstore (http://www.grippersuperstore.com/store.aspx?cat_id=26&prod_id=2020) and David Horne's World of Grip (http://www.davidhorne-gripmaster.com/shop.html#blocks) sell them. I recommend you get one from each and you will have four different sizes to work with. Quote Link to comment Share on other sites More sharing options...
rolf Posted June 17, 2012 Author Share Posted June 17, 2012 (edited) you're referring to 'set blocks'. Grippersuperstore (http://www.grippersu...26&prod_id=2020) and David Horne's World of Grip (http://www.davidhorn...hop.html#blocks) sell them. I recommend you get one from each and you will have four different sizes to work with. Thanks, but those are actually used for working from partial close to full close, I'm looking for something for working from fully open to partial close (e.g. 4 mm). Edited June 17, 2012 by rolf Quote Link to comment Share on other sites More sharing options...
Cannon Posted June 17, 2012 Share Posted June 17, 2012 Jordan R. uses blocks of wood. Quote Link to comment Share on other sites More sharing options...
chilliman64 Posted June 17, 2012 Share Posted June 17, 2012 you're referring to 'set blocks'. Grippersuperstore (http://www.grippersu...26&prod_id=2020) and David Horne's World of Grip (http://www.davidhorn...hop.html#blocks) sell them. I recommend you get one from each and you will have four different sizes to work with. Thanks, but those are actually used for working from partial close to full close, I'm looking for something for working from fully open to partial close (e.g. 4 mm). you can still use these to close the handles onto but yeah, you won't get down to 4mm as the GHP is 15mm on the short side and the DH is 20mm. maybe just work with several stacks of coins taped together, they don't cost much and there's no postage either. Quote Link to comment Share on other sites More sharing options...
chilliman64 Posted June 17, 2012 Share Posted June 17, 2012 you're referring to 'set blocks'. Grippersuperstore (http://www.grippersu...26&prod_id=2020) and David Horne's World of Grip (http://www.davidhorn...hop.html#blocks) sell them. I recommend you get one from each and you will have four different sizes to work with. Thanks, but those are actually used for working from partial close to full close, I'm looking for something for working from fully open to partial close (e.g. 4 mm). you can still use these to close the handles onto but yeah, you won't get down to 4mm as the GHP is 15mm on the short side and the DH is 20mm. maybe just work with several stacks of coins taped together, they don't cost much and there's no postage either. sorry - the GHP is 25mm at the narrrowest point (how do you edit posts?) Quote Link to comment Share on other sites More sharing options...
rolf Posted June 17, 2012 Author Share Posted June 17, 2012 (edited) you can still use these to close the handles onto but yeah, you won't get down to 4mm as the GHP is 15mm on the short side and the DH is 20mm. maybe just work with several stacks of coins taped together, they don't cost much and there's no postage either. Yep, I think the coin stacks would make the most sense. They're a bit flimsy, but they do work. The ready-made pieces would have been more cool than necessary. (There's an Edit link to the left of your own post's MultiQuote button that is just barely visible until you move the pointer close to it, quite hard to notice) Edited June 17, 2012 by rolf Quote Link to comment Share on other sites More sharing options...
Electron Posted June 17, 2012 Share Posted June 17, 2012 I use a stack of half dollars, easy to hold in the off-hand and enough surface area to pinch between the grippers. Quote Link to comment Share on other sites More sharing options...
chilliman64 Posted June 17, 2012 Share Posted June 17, 2012 (edited) thanks rolf, seems I only have a feint Report button, will write the admin team and see if there is a problem edit - now the button appears! I'm sure it wasn't there before Edited June 17, 2012 by chilliman64 Quote Link to comment Share on other sites More sharing options...
Electron Posted June 18, 2012 Share Posted June 18, 2012 It's because you can only edit your post right after you comment. Quote Link to comment Share on other sites More sharing options...
chilliman64 Posted June 18, 2012 Share Posted June 18, 2012 rolf - a deck of cards held together by a rubber band might work also (thanks tentacle - I now see that the edit button is temporary) Quote Link to comment Share on other sites More sharing options...
rolf Posted June 20, 2012 Author Share Posted June 20, 2012 rolf - a deck of cards held together by a rubber band might work also That's actually a great idea. I'll probably stick to my coins for now, but the card deck would allow very precise thicknesses if I ever need to "microload" gap-wise. Quote Link to comment Share on other sites More sharing options...
RTvG Posted June 20, 2012 Share Posted June 20, 2012 I've taped together a stack of coins that measures 12 mm thick. Then I'll remove coins from the stack every now and then. This will work, but I was wondering if anyone makes something that could be used for this kind of training with "target gaps". The CoC Key will not work, as it's meant for measuring the gap and thus the different thickness surfaces are way too tiny to aim at. Actually the coc key is exactly this what it does. you hold it on the dogleg when closing, and when it touches, you know the distance. You can start at 18mm, and work your way to full close in steps of 2mm. It's exactly what you describe. But, to my findings, the coc key is just too tiny and therefore not practical to work with. Bob Quote Link to comment Share on other sites More sharing options...
RTvG Posted June 20, 2012 Share Posted June 20, 2012 ps, If you might own a coc key already, guess it's better value to drill a hole through and use it as a silver bullet Quote Link to comment Share on other sites More sharing options...
bencrush Posted June 20, 2012 Share Posted June 20, 2012 I used to use a stack of pennies that I taped together with duct tape. Held together quite well if you use enough duct tape on them. Micro-loadable. Use dimes if you want an inbetween width or a quarter if you want thicker. Nickels work too of course. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.